Page 1 of 9

Journal for Studies in Management and Planning

Available at http://internationaljournalofresearch.org/index.php/JSMaP

e-ISSN: 2395-0463

Volume 01 Issue 08

September 2015

Available online: http://internationaljournalofresearch.org/ P a g e | 208

Development ofA Motorized Wet Soybean De-Hulling Machine

Ogunsola F.O1., Ogundare S.O2., Jimo K.A3 and Oyeniyi A.O.

4

Department of Agricultural and Bio-Environmental Engineering,

Oyo State College of Agriculture and Technology,

Igboora, Oyo State, Nigeria.

Abstract –

Soybeans for several reasons is a valuable

and economical agricultural commodity. It

has favourable agronomic characteristics

including good adaptability to a wide

range of soil and climate. The soybean has

been recognised as so versatile that it can

be processed into a wide variety of food

products. The soybean can be wet or dried

processed. The intake of soybean milk that

is gaining acceptability both by the rural

and urban dwellers calls for industrial

production of the milk. This development

leads to this work (development of a

motorized wet soybean de-hulling

machine). The de-hulling of soybean

machine was based on abrasion between

the beans and the wall of the de-hulling

chamber and between the beans. The

machine consists of the inlet hopper, the

de-hulling chamber which included the

barrel and the auger specially designed to

create abrasion on the beans as it is

carrying them towards the outlet end, 1 hp

geared motor with pulley and belt to make

up the transmission unit, water dosing unit

and the frame on which the whole

equipment rests. The overall dimensions of

the machine are 460mm x 750mm x

250mm. the machine was tested and the

results show that the average throughput

capacity is 171Kg/hr with de-hulling

capacity of 150Kg/hr and efficiency of

92%. The output result falls within

economic range, therefore it is

recommended for small soybeans

processors.

Key words: De-hulling machine;

Soybeans; Throughput Capacity; Design;

Efficiency

INTRODUCTION

Soybean [Glycine max (L.) Merr.] is an

important oil seed belonging to the family

leguminosae and is usually grown as a

food crop. There are three species of

soybean which include: Glycine

Ussuriensis – Wild, Glycine Max –

cultivated and Glycine Gracilis –

intermediate. But Glycine Max is

commonly grown throughout the world as

a commercial material. Soybean is mainly

cultivated for its seeds, used commercially

as human food and livestock feed and for

the extraction of oil. The oil is produced

almost entirely for human consumption,

while the meal is mainly used as animal

feed. Soybean seed may be planted in

cultivated or tilled soil by a tractor and a

planter which deposits the soybean seed

about 38mm deep in rows that are up to

762mm apart. There is no rule about how

wide rows must be, but 760mm is typical.

Soybean should be harvested when they

are plump and green. When the rest of the

plant begins turning yellow, the beans are

still edible but past their prime. If the

beans themselves begin to turn yellow,

they should no longer be harvested for

human consumption (Siegel and Fawcett,

1976). It can be harvested manually by

handpicking or mechanically using a

combine harvester. Soybean contains a

Page 2 of 9

Journal for Studies in Management and Planning

Available at http://internationaljournalofresearch.org/index.php/JSMaP

e-ISSN: 2395-0463

Volume 01 Issue 08

September 2015

Available online: http://internationaljournalofresearch.org/ P a g e | 209

high level of some essential nutrients such

as protein and lipid. It also contains

relatively high amount of zinc and thus,

serve as an important dietary source.

Soybean has favourably agronomic

characteristics, including good adaptability

to a wide range of soil and climate. It has a

unique chemical composition on an

average matter basis; it contains about

40% proteins and 20% oil. With this

composition, it ranks highest in terms of

protein content among all the food crops

and also ranks highest with respect to oil

content among all food legumes (Liu,

2000, 1997).

II. MATERIALS AND METHODS

2.1 Materials Used

Table 2.0: The materials used in construction of soybean de-hulling machine are listed

below:

S/N PARTS MATERIAL USED

1 Hopper Galvanized Plate

2 Frame Angle Iron 2’’

3 Driving Shaft Mild Steel

4 De-hulling Chamber Galvanized Plate

5 Bearing Pillow bearing P208

6 Pulley Mild Steel

7 Drill Bit (7 & 12mm)

8 Bolts & Nut (10 & 19mm)

9 Cutting Disc

10 Grinding Disc

11 Electrode

2.2 Conceptual Design

The conception was based on the principle

of abrasion therefore the auger was

designed to initially move the seeds

forward then a reverse auger to create back

pressure so as to develop a rubbing force

between the seeds and the walls of the

barrel. The reverse auger’s height was less

than the height of the forward auger this

caused the overall forward movement of

the seeds. The flight at the end of the shaft

helps to discharge the de-hulled beans. The

details of the shaft is as shown in fig 1

below

Page 3 of 9

Journal for Studies in Management and Planning

Available at http://internationaljournalofresearch.org/index.php/JSMaP

e-ISSN: 2395-0463

Volume 01 Issue 08

September 2015

Available online: http://internationaljournalofresearch.org/ P a g e | 210

Fig. 1 The conceptual design of the De-hulling shaft

The barrel was made of two halves, the

lower half is perforated and the upper half

carried the input hopper and the water

dosing point. At 50 rpm 1hp geared motor

was used with ratio 1:2 pulley for power

transmission via belt. While the whole

arrangement was supported on a sturdy

frame made of 70 x 70 x 5mm angle bar.

The conception was as shown in fig. 2

Fig. 2: The conceptual design of the De-hulling Machine

C:\Users\User\Desktop\Autocad!\View!\Isometric View!.bmp