Page 1 of 12

Journal for Studies in Management and Planning

Available at http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 1

January 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 62

An Investigation to Ascertain the Commitment of

Management Personnel towards the Implementation

Of Safety Regulations in Technical Institution Workshops

Idjawe Ewherunu Emmanuel

Metalwork Department Federal college of Education (Technical) Asaba

Delta-State Nigeria

Abstract

This study was carried out in order to

ascertain the commitment of management

personnel towards the implementation of

industrial safety regulations in Technical

Institution workshops. To guide the study,

two research questions was raise and one

hypothesis formulated and tested at 0.05

level of significance. The study adopted a

survey research design, the population

comprised of 30 chief executive and Heads of

department drawn from different Technical

Institutions in Delta State of Nigeria.

Twenty-four item statements were developed

to elicit information from the respondents

.Mean statistic was used to answer the

research questions, while t-test was used to

test the hypothesis. The result of the analysis

revealed that management personnel in

Technical Institutions do not show

commitment to the implementation of

industrial safety regulations in Technical

Institution workshops, rather they delegate

safety responsibilities. Conclusion was

drawn and some recommendations were

made to include: A written safety policy

statement that is signed by the chief

Executive should be displayed to the

knowledge of staff, students and visitor,

chief executive should provide financial and

human resources to safety implementation,

among others.

Key words: Commitment, Management

Personnel, Safety

Regulations and Technical

Institution workshops.

Introduction

Commitment is the willingness to

give your time and energy to something that

you believe in. It entails dedication to a

particular cause nor belief and the

willingness to get involved. In an

organization, people who are committed

always make effort and stick to such effort in

order to gather momentum to advance the

goals of such an organization and the more

people are committed, the more effective

they influence others. Management

Personnel commitments implies the direct

participation by the higher echelon of an

organization by showing passion and interest

either by formulating polices, setting up

targets or benchmarks to advance the cause

of such organization. On the other hand,

implementation of safety regulations in

Technical Institution workshops is the

adherence to established safety guidelines in

order to ensure the safety of workers,

students and others who may have been in

such environment. However, workshop

activities in Technical institutions are aimed

at the production and maintenance of

Page 2 of 12

Journal for Studies in Management and Planning

Available at http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 1

January 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 63

component. In an attempt to accomplish a

given task, staff and students may be face

with inherent hazards that could cause an

accident if care is not taken such an accident

could claim lives, destroy properties or can

even cause extensive damage to the

environment. Hence, it is always important

for safety awareness to be created and

sustained in the mind of everyone in such

work environment.

However, workshop activities in

Technical Institution are aimed at the

production and maintenance of components,

and in an attempt to accomplish a given task,

staff, students and those within such

environment are faced with inherent hazards

that could cause serious damage. Hence, it is

always important for safety awareness to be

created and sustained in the mind of

everyone in such environment.

Wikipedia encyclopedia (2015),

defined safety as a state of being “safe”. It is

a condition of being protected against

physical, social, political, occupational or

other types of consequences of failure,

damage or any other non-desirable event. On

the other hand, industrial safety can be seen

as the control of recognize hazards in

workplaces in order to achieve an acceptable

level of risk. This can take the form of being

protected from exposure to something that

causes health risk or economic loss in the

form of people and assets.

Safety issue is a major source of

concern to all stakeholders in any

organization, right from the Chief Executive

Officer to the least personnel, and that is why

there is a common slogan that says

“SAFETY FIRST”. Onyekakeyah (2008)

asserted that everyone should be made

conscious of safety in all job situation no

matter the services or operations carried out,

or how highly placed an individual is in any

organization, because the basic underlying

principle of any safety management system

that help to enhance the reputation of any

organization to the outside community is

safe operation.

For any safety programme to be

successful, it has to get the support and

commitment of management, because a

sound safety performance reflect overall

good management of such an organization.

Adigo (2008) asserted that several studies

that have been carried out to measure relative

success of safety performance have shown

that where a substantial improvement in

performance has been achieved, the major

factor responsible for such achievement is

the personnel and visible commitment by

management. Without transparent leadership

and good support from management, no

safety effort can survive. Hence the

Page 3 of 12

Journal for Studies in Management and Planning

Available at http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 1

January 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 64

management of safety in Technical

Institution workshops operation has to be

seen as an essential part of management

personnel range of responsibilities as they

should show serious concern as a basis of

commitment.

However, there are safety laws

guiding workplaces, these laws are enacted

for employers to ensure the safety of persons

at work, protection of assets and the

environment. Consequently, safe operating

procedures are developed by employers to

ensure compliance with these laws.

Management of Technical institutions

must be aware of the existence of these laws.

However with heavy commitment of meeting

institutional objectives i.e., the training of

students, most Technical institution

management personnel believe they have no

direct involvement with safety regulations

and implementation, therefore they delegate

safety responsibilities to workshop

instructors and other front line officers,

which have direct contact with students. This

practice does not reflect the true purpose of

safety in the workplace. Management

personnel need to understand the objective of

these laws to be able to appreciate safety

recommendations and make necessary input

to establish appropriate policies that would

ensure compliance with these laws and

ensure effective safety of students in the

cause of training and the safety of workshop

personnel.

The Nigerian Institute of Safety

Professionals Training Manual (2006),

contain a model code of safety regulations by

International Labour Organization (ILO)

which is designed to improve the health and

safety of workers in the workplace. Nigeria

as a nation and being a member of ILO

ratified and adopted this model code of

safety regulation as the factory Act of 1990

with the following objectives:

1. To secure the health, safety and

welfare of persons at work.

2. Protect persons at work against risks

to health or safety arising out of in

connection with activities of persons

at work.

3. Involve everyone both management

and employees and make them aware

of the importance of safety.

Furthermore, part XI of the Act

defined a factory as any premises in which

the following purposes are attain:

1. The making of any article or part

of an article.

2. The altering, repairing

ornamenting, etc. of an article.

These are the ambit of which

workshop activities in Technical

institutions are centered on.