Page 1 of 10

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 9

September 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 230

Experimental studies on various characteristics of cement

mortar embedded with bacterial species

1 K. Venkatesh Reddy,

2Mr. D. Aditya Sairam,

1Mandava Institute of Engineering and Technology,

Vidya Nagar, Krishna District, Jaggayyapet, Andhra Pradesh, 521175

2M-Tech. Assistant Professor

Abstract:

Microbially induced calcium carbonate precipitation

(MICCP) is a novel method for the protection of

cement-based materials. This paper deals the

comparative studies on strength characteristics in

microbial cement mortars which were treated by

Enterobacter sp. M2 microorganism in different

calcium source (calcium hydroxide, calcium acetate,

calcium chloride and calcium oxide) with various

curing process. The crystalline phases of calcium

carbonate (CaCO3) crystals formation and the

surface morphology of cement mortar were

investigated by X-ray diffraction (XRD) and

scanning electron microscope (SEM). Cement mortar

specimens with and without addition of bacterial

species were casted and ~ 44% increase in

compressive strength, ~56% in tensile strength was

noticed while compared to control specimen (without

bacteria). Surface treatment of specimen with

bacteria resulted around ~40% decrease of water

absorption and increases the resistance to water and

hazard material penetration, mainly attributed to its

pore blocking effects. This biological surface

treatment shows promising prospect for increasing

durability aspects of concrete/cement mortar.gth and

durability of microbial cement mortars.

In the present study a noteworthy enhancement

of compressive strength of 45% and tensile strength

of 12% compared to control is observed in the bio

curing cement mortar specimens embedded with EB1

relative to control. Similarly the cement mortar

specimen embedded with EB2 shows higher

compressive strength of 29% and tensile strength of

13% compared to control cement mortar specimen.

This method of implant semi-solid mixture on to

the surface of cement mortar specimen shows

significant effects such as decrease of permeability

and capillary penetration. EB2 embedded specimen

show 56% decrease of water absorption and

increase resistance to water penetration and acid

resistance in the cement mortar specimen embedded

with EB1 and EB2 shows 13 and 9 times reduction in

water sorptivity coefficient respectively compared to

control specimen

Keywords

Calcium carbonate, Compressive strength, Tensil

e strength, Sorptivity, MICCP.

1. Introduction

Microbial calcium carbonate precipitation in a

cement mortar/concrete is a complex mechanism. In

nature the CaCO3 precipitation is accompanied by

biological process. Based on continuous research a

number of innovations have been made from time to

time to improve the strength and durability

performance [1] of cement mortar/concrete.

Bacterially induced CaCO3 and mediated

mineralization is a research subject which was

widely studied in the past decade [2-4]. Use of

microorganism with in cement mortar/concrete

leading to the process of bio mineralization is a

potential field of research in concrete technology [5,

6]. Abundant significance of microbially induced

calcium carbonate precipitation (MICCP) so called

carbonatogenesis has put much awareness from both

basic and applied point of view in civil engineering

field [7]. The CaCO3 precipitation is a function of

ionic strength and pH in the medium [8]. The

increase of compressive strength of mortar is due to

complex interaction between the bacterium and

cement matrix [6].

The presence of MICCP in the cement mortar

through XRD and scanning electron microscope

(SEM) had been analyzed and reported [9] that the

crystallization of CaCO3 as vaterite (V), aragonite

(A), calcite (C). Even though the cement

mortar/concrete is relatively strong mechanically, but

it suffers by low tensile strength, permeability to

liquid and consequent corrosion of reinforcement,

susceptibility to chemical attack and low durability.

The cement mortar/concrete is not usually expected

to resist the direct tension because of its low tensile

strength and brittle nature. However, the

determination of tensile strength of cement

mortar/concrete is necessary to determine the load at

which the cement mortar/concrete members might

crack. The presences of MICCP in cement

mortar/concrete affect the compressive strength and

indirect split tensile strength [10-14].

venkateshreddy.civil2010@gmail.com

Page 2 of 10

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 9

September 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 231

The increased compressive strength and split

tensile strength was noticed while varying the cell

concentration [15]. The bio deposition treatment

resulted in an increased resistance of mortar

specimens towards carbonation, chloride infiltration

and freezing–defrosting [16-18].

The durability and life of cement mortar/concrete

specimens is estimated by the capillary water

movements into it. Higher absorption of water by the

specimen would imply higher damage and vice

versa. The influence of microbial cement

mortar/concrete on penetration properties had been

studied and analyzed [10,19]. The bacterial treated

specimens were found to have better resistance

towards chloride penetration as compared to control

specimens [20]. A decreased water permeability of

bioremediated cement mortar cubes treated by

Sporosarcina pasteurii bacteria was reported [10]

along with six times reduction in absorption of water

upon treatment of mortar cubes with Bacillus sp. CT- 5 as compared to control specimens. Some other

factors like, initial moisture content or saturation

[21], compaction [22] and curing time [23] were

mostly influencing capillary water transport. Weight

loss, reduction in compressive strength, and change

in dynamic modulus of elasticity are used to evaluate

the extent of cement mortar/concrete deterioration

due to acid attack.

A successful attempt has been made on the

biomineralization process to enhance the

compressive strength, indirect split tensile strength

and durability of cement mortar/concrete by using

the Enterobacter sp. M2 (EB) microorganism in

different calcium source and curing process. The

present work deals with the measurement and

comparison of compressive strength, indirect split

tensile strength, acid attack and water permeation

properties of the cement mortars.

2. Experimental

Ordinary Portland Pozzolana Cement conforming

to IS 1489:1991 with specific gravity of 3.1 was used

to prepare the cement mortar specimens. Locally

available clean river sand conforming to IS 650:1991

with specific gravity 2.7 and fineness modulus 2.96

was used as fine aggregate. The microorganism (EB)

was collected from Central Electrochemical

Research Institute, Karaikudi, Tamilnadu which were

isolated from cooling water towers for bacterial

treatment. B4 broth medium was prepared from 0.5%

yeast extract, 0.5%glucose and 1% calcium acetate

solution and EB is added. Then the solution was

shacked at 30° C (using orbital Shaker) for 3 days

with 150 rpm to grow and multiply the bacterial

species (EB). After the centrifugation the supernatant

was extended to the optical density (600nm) of 1 in

UV/ VIS Spectrometer. Then 3ml of EB was added

with B4 broth medium then it was mixed with

different bacterial culture grown sources which

contains 8g nutrient broth, 2% Urea with different

calcium sources of 25mM calcium hydroxide

(Ca(OH)2), calcium acetate (Ca(CH3COO)2 ),

calcium chloride (CaCl2) and calcium oxide (CaO)

respectively (represented as BCGS1, BCGS2,

BCGS3 and BCGS4).These calcium sources were

kept separately for 3 to 5 days to observe the

variation of pH value.

To carry out testing procedure, each cement

mortar specimens were cast with 70.6 X 70.6 X

70.6mm size by using 98.7ml of BCGS1, BCGS2,

BCGS3 and BCGS4 along with 210g cement, 630g

river sand by cement to sand ratio of 1:3 (by weight)

and water to cement ratio 0.47 respectively as per IS

4031 – 1988. Similarly each cement mortar

specimens without bacterial species (using plain

calcium sources without EB) was cast for control

specimen with above specification. Initially cement

and sand was thoroughly mixed (dry mix), then

different bacterial cultural grown sources was added

into mixture separately to obtain cement mortar

paste. Each cube was prepared by filling the mortar

in an empty mold by 3 layers with compacted in 25

blows. In normal curing, potable water is used for

mixing and curing the microbial cement mortar

specimen. In bio curing, different bacterial culture

growth sources (BCGS) along with EB

microorganism is used for mixing and curing the

microbial cement mortar specimen (i.e. the microbial

cement mortar specimen is immersed into bio

solution of BCGM along with EB or SB).

To analyze the compressive strength of normal

and bio curing specimens, they were individually

tested by using Computerized Universal Testing

Machine (CUTM). The cube specimens were placed

in the machine such that the load is applied to the

opposite sides (not to the top and bottom). The axis

of the specimen was carefully aligned with the centre

of the thrust of the spherically seated platen without

any backing materials in between specimen and steel

platen of the testing machine. Then the load was

applied gradually without shock at the rate of

140kg/cm2/min until the resistance of the specimen

to the increasing load breaks down. The maximum

given load to the specimen was recorded. The test

was repeated with regular intervals (7, 14, 21 and 28

days) and experimentally recorded compressive

strength in different curing process of the cubic

specimen was tabulated.

The splitting tests are well known indirect tests

used to determine the tensile strength of cement

mortar/ concrete.

The specimen cylinder (50mm diameter and

100mm length) were prepared from the mixture of

cement to sand ratio 1:3 (by weight) and water to

cement ratio 0.47 as per IS 4031 – 1988 along with

Page 3 of 10

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 9

September 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 232

three layers, each having 25 blows. The test

consisted of applying a compressive line load along

the opposite generators of a specimen placed with its

axis horizontal between the compressive platens. To

prevent multiple cracking and crushing at the points

of load applied, the load was distributed through two

bearing strips whose width is b (b=30mm).

To calculate the sorptivity coefficient the different

normal, bio cured specimens (50mm diameter and

100mm length of cylinder) were dried at 100°C in a

ventilated oven after curing of 28 days. Then the

specimens were coated with two layers of water

proof resin of ISO 0081 at all outer surfaces except

top and bottom of the cylindrical specimen to ensure

unidirectional absorption through the non-treated

side. The specimens were submerged to 5mm of

water with the non-treated side facing downward

while the water level approximately 2 mm above the

base of the specimen. At regular time intervals (15

min, 30 min; 1 h, 1.5 h, 3 h, 5 h, 8 h, 24 h, 72 h, 96 h,

120 h, 144 h, and 168 h), the specimens were

removed from the water and weighed after drying the

surface with a wet towel. Immediately after the

measurement, the test specimens were sunken again

to continue the observation to obtain saturated value

of water infiltration.

3. Instrumentations

Optical density of the B4 broth medium was

analyzed by using Lambda 35 UV/VIS spectrometer

(Perkin Elmer- USA). The sophisticated instruments

like, Forma orbital Shaker (model: 420, S.No:13500-

1712), Thermo Electron Corporation (Hong Kong)

LTD and Computerized Universal Testing Machine

(CUTM) with capacity of 1000kN, accuracy of

0.1kN, Fine Spray Associates & Engineering PVT.

Ltd, Maharashtra, India was used to grow the

microorganism and to analysis the compressive

strength of cement mortar cubes respectively. Micro

structure of the specimen (formation of calcium

carbonate) was analyzed with high resolution (3.0

nm-30kV) JSM-6390 Scanning Electron Microscope

(SEM), USA with magnification of 5 to 300,000.

The elemental analysis was carried out with XRD

6000 Shimadzu- Japan. Water absorption in

specimen was experimentally analyzed and the

results are discussed.

4. Microorganism and its Activity

The key point of the present study is to select the

suitable microorganism (bacterial species) and

incorporate into cement mortar for its efficient

activation. Possible biochemical reaction in the

medium (Stocks-Fischer et al., 1999) such as urease

catalyzed hydrolysis of urea to precipitate CaCO3 at

a cell surface that provides a nucleation site is given

below:

As a result CaCO3 particles were precipitated

gradually between cement sand matrix and on the

surface of the Specimen.

Page should be of A4 size with normal margin.

All printed material, including text, illustrations, and

charts, must be kept within a print area. Do not write

or print anything outside the print area. All text must

be in a two-column format. Text must be fully

justified. A format sheet with the margins and

placement guides is available in Word files as

<format.doc>. It contains lines and boxes showing

the margins and print areas. If you hold it and your

printed page up to the light, you can easily check

your margins to see if your print area fits within the

space allowed.

5. Results and Discussion

Variation of pH and microbial activity

Urease catalyzed hydrolysis of urea to precipitate

CaCO3 at a cell surface was prepared from various

calcium sources. The pH value increases from 7.4 to

10.1 (within 30 hrs) in different calcium sources

which confirm the presence of bacterial activity. The

observed result is compared with earlier reported

data and the graph is drawn (as shown in figure 1).

The pH value is unaltered even when time duration

increases from 0 to 30hrs in the bacterial culture

growth solution in the absence of microorganism. As

time increases, the pH also increases in the BCGS1,

BCGS2, BCGS3 and BCGS4 as shown in the figure

1. Due to the enrichment activity of bio chemical

reaction by the EB microbial bacteria in calcium

hydroxide source, a large difference of pH value is

noticed in between BCGS and BCGS1.