Page 1 of 9

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 11

November 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 361

Teaching Learning Based Optimization Applied To

Mechanical Constrained Design Problems

1K. Ramesh,; 2 Mr. Srv. Narsaiah

1

pg Scholar, Depeartment of Mechanical Engineering, Srisai Educational Society's Group

of Institutions-Kodad

2 Assistant Professor, Depeartment of Mechanical Engineering, Srisai Educational

Society's Group of Institutions-Kodad

ABSTRACT:

In the midst of all evolutionary optimization

algorithms to improve teaching and learning

based (TLBO) seems to be a promising

technique with a relatively competitive offer.

It is better that some of the standard

functions known in the upper limit of tests,

limited mechanical design, and nonlinear

numerical optimization problems persist.

This thesis provides the application of

different TLBO problems in mechanical

engineering. Both have been restricted and

action unrestricted in some of the

manufacturing processes and design

problems. , Parametric optimization of the

three operations were carried out

unconventional machining of an electric

discharge machining, and the manufacture

of electrochemical and electrical discharge

machines and chemical machining results

are compared with other evolutionary

algorithms. Improvement in the TLBO

algorithm in this thesis using the two

systems have been incorporated are a small

series of startups and replace the worst

solutions with new ones. It has been to

evaluate the performance of these

modifications in this thesis by solving the

problems of the six optimized using the

proposed TLBO original amendments. It has

been found that better access to global

optimal values through the use of these

modified results obtained. However, the

results would prefer to use a small set of

mutations to replace the worst solutions

with new solutions, in addition to the

original planned TLBO logic. Boom wise

and slightly worse solutions replace with

new ones, an additional advantage of the

current algorithm tested. If these

modifications led to the convergence of the

most clear types, and finally introduced the

optimal solutions globally, and in some

cases rather than the results that solutions

have already been deployed.

Page 2 of 9

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 11

November 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 362

INTRODUCTION:

Conventional machining processes require

that the work piece material to be stressed

beyond the yield point to achieve material

removal. This certainly requires the cutting

tool to be harder than the work piece

material. Alloys with alloying elements such

as tungsten, chromium, vanadium,

molybdenum etc, have high hardness, high

heat resistance and high strength to weight

ratio. Machining of such alloys by

conventional means is difficult as well as

time consuming. Hence, there is a need to

develop better machining processes to

handle the shortcoming of the conventional

processes. As a result, these processes are

termed as nontraditional machining

methods. The main reasons for the

development and use of new machining

processes are stated below. 1. High strength

alloys or brittle materials: The hardness of

the work piece material (typically above

400HB) is often harder than the cutting tool

material or when it becomes necessary to

machine hardened materials. 2. Complex

shapes and surfaces: Particularly in

manufacturing of moulds and dies, complex

shapes and surfaces are required to be

produced on already hardened materials. In

such cases, it is a necessity to use more

advanced machining processes. Sometimes,

the work piece is too flexible, slender, or

delicate to withstand the cutting or grinding

forces, or the parts are too difficult to fix. 3.

Accuracy and surface finish: High

accuracies on dimensions and better surface

finish on hard materials are often produced

by slow conventional machining

accompanied by a number of finishing

processes. This makes the process

uneconomical and time consuming. Also the

temperature rise and residual stresses in the

work piece are not desirable or acceptable.

4. Difficult geometry: With addition to

complex geometries, it is also required to

produce long holes with length to diameter

ratio greater than 100 or produce holes of

diameter less than 0.1 mm. These

requirements have led to the development of

chemical, electro-chemical, thermal, electro- thermal, mechanical, and other means of

material removal. Over the last four decades,

there has been a large increase in the number

of non-traditional machining processes

(NTMP) [1]. Today, non-traditional

machining processes with vastly different

capabilities and specifications are available

for a wide range of applications. These

processes are classified according to the

nature of energy employed in machining as

Page 3 of 9

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 11

November 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 363

discussed below [1]: 1 Chemical and

electro-chemical processes like chemical

milling, electro-chemical machining,

electro-chemical grinding, electro-chemical

honing etc. 2 Thermal and electro-thermal

processes like electric discharge machining,

laser beam machining, plasma arc

machining, electron beam machining, and

ion beam machining etc. 3 Mechanical

processes like ultrasonic machining,

abrasive jet machining, and water jet

machining etc. 4 Hybrid processes like

electro-chemical discharge grinding,

abrasive electrical discharge machining,

vibration-assisted electro-chemical

machining etc

Electro-Discharge Machining (EDM)

Formation of craters by electric discharges

on cathode was first reported by Joseph

Priestley in 1766. His observations are as

follows [2]: “After discharging a battery, of

about forty square feet, with a smooth brass

knob, I accidently observed upon it a pretty

large circular spot, the centre of which

seemed to be superficially melted. (...) After

an interruption of melted places, there was

an entire and exact circle of shining dots,

consisting of places superficially melted,

like those at the centre.” “Examining the

spots with a microscope, both the shining

dots that formed the central spot, and those

which formed the external circle, appeared

evidently to consist of cavities, resembling

those in the moon, as they appear through a

telescope, the edges projecting shadows onto

them, when they were held in the sun.”

Since then electric discharges have been

used for a variety of tasks including material

removal which was attempted by Russian

scientists Boris and Natalya Lazarenkoat at

Moscow University in 1943. The interest in

spark machining initiated a number of

studies and research in the 1950s.

LITERATURE REVIEW:

ELECTRO-DISCHARGE MACHINING

(EDM) A thermal model simulating

discharge super position and capable of

representing postEDM surfaces was

presented by Izquierdo [19]. It was

concluded that location, discharge and

development of temperature fields on

irregular surfaces affected the material

removal rate as much as 50% due to the

superposition of multiple discharges. Using

a finite element based model and

considering the effect of superposition of

multiple discharges the temperature fields

inside the work piece was calculated and

based on this the machined surface was

generated. Tantra et al. [20] proposed a