Page 1 of 5

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 11

November 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 347

Performance of Single Cylinder Diesel Engine Uses Bio- Diesel

1v. Raju; 2. Mr. B. Venkata Narayana

1pg Scholar, Depeartment Of Mechanical Engineering, Gandhi Academy Of Technical Education-Kodad

2 Assistant Professor, Depeartment Of Mechanical Engineering, Gandhi Academy Of Technical Education-Kodad

ABSTARCT:

In recent years, much research has been

carried to find suitable alternative fuel to

petroleum products. In the present

investigation experimental work has been

carried out to analyze the performance and

emissions characteristics of a single

cylinder compression ignition DI engine

fuelled with the blends of mineral diesel and

biodiesel at the different injection pressures.

The optimal value of the injection pressure

was observed as 200 bar in the range of 180

to 220 bar. The performance parameters

evaluated were brake thermal efficiency,

break specific fuel consumption and the

emissions measured were carbon monoxide

(CO), carbon dioxide (CO2), hydrocarbon

(HC), and oxides of nitrogen (NOx). The

results of experimental investigation with

biodiesel blends with diesel are compared

with that of diesel. The results indicated that

the CO emissions are slightly less, HC

emissions were also observed to be less for

B10 and B20, and NOx emissions decreased

by 39 % for B10 and 28 % for B20

compared with B100. The brake thermal

efficiency of the engine decreased around

6% for all blends in comparison with diesel,

and the break specific fuel consumption was

slightly more for B10 and B20.

INTRODUCTION:

In 1911, Rudolf Diesel presented the world

with the compression ignition engine, which

at that time did not have a specific fuel.

Diesel claimed that the engine could be fed

by vegetable oils which could help the

agricultural development in countries using

this engine. Biodiesels are derived from

vegetable oils or animal fats, more

specifically the alkyl esters from these. The

esters from vegetable oils are considered to

be superior since they have a higher

energetic yield and essentially no engine

modifications are necessary for their use.

Biodiesels have been traced back to the mid- 1800s, where transesterification was used to

make soap and the alkyl esters (biodiesels)

were just considered byproducts. Early

Page 2 of 5

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 11

November 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 348

feedstocks were corn, peanut, hemp oils, and

tallow. In 1973, the OPEC nations cut down

their oil exports to the West, resulting in the

oil crisis of the 1970s. Prices of oil increased

dramatically and people started to look into

renewable sources of energy. Many of the

federal renewable energy programs were

initiated during the 1970s including the

National Renewable Energy Laboratory.

Once prices began to fall in 1979, tax

incentives and other support for the

renewable energy industry ended thanks to

shortsighted policies. The initial steps taken

toward a renewable energy initiative were

abandoned. In recent years, oil prices have

been rising rapidly again and there is a

major concern for the long term availability

of fossil fuels. This and the growing concern

for our environment have created a much

larger market for renewable resources. The

idea of using vegetable oils instead of fossil

diesel fuels has resurfaced as a way to

minimize the net carbon footprint left by

emissions from compression ignition (CI)

engines. Straight vegetable oils (SVOs) have

their fair share of problems in unmodified

CI engines. These problems include: cold- weather starting; plugging and gumming of

filters lines, and injectors; engine knocking;

coking of injectors on piston and head of

engine; carbon deposits on piston and head

of engine; excessive engine wear; and

deterioration of engine lubricating oil.

Vegetable oils decrease power output and

thermal efficiency while leaving carbon

deposits inside the cylinder. Most of these

problems with vegetable oil are due to high

viscosity, low cetane number, low flash

point. For the past decade, there has been

increased interest in using biodiesels instead

of fossil diesel in CI engines. The use of

biodiesel was not economically feasible

until recently due to rise in prices of fossil

fuels. There is a significant amount of

research being conducted to lower the cost

of producing biodiesel as well as to increase

its performance in CI engines. Biodiesels

have a higher viscosity and specific gravity

than fossil diesel, which affects fuel

consumption, injection timing, and spray

pattern. Since the cetane number, a measure

of combustion quality, for biodiesels is

higher when compared with fossil diesel

(No. 2 fuel oil), a shorter ignition delay will

result which will require an advance of

combustion timing. Canakci and Van

Gerpen showed that B100 (100% soy

biodiesel) had a higher brake specific fuel

consumption (BSFC) when compared to

Page 3 of 5

Journal for Studies in Management and Planning

Available at

http://edupediapublications.org/journals/index.php/JSMaP/

e-ISSN: 2395-0463

Volume 02 Issue 11

November 2016

Available online: http://edupediapublications.org/journals/index.php/JSMaP/ P a g e | 349

fossil diesel. This reflects its lower heating

value (about 12% lower than diesel).

BIODIESELS

A brief overview of the production of

biodiesels and the use of various

components used is given here. There are

many methods that can be used to make

biodiesels with multiple combinations of

catalysts, neutralizers, and feed stocks. After

reviewing the general and most popular

methods, the ones used to create our test

samples will be explained in greater detail.

Overview

Organic Chemistry

The major components of vegetable oils are

triglycerides. Triglycerides are esters of

glycerol with long-chain acids (fatty acids).

The composition of vegetable oils varies

with the plant source. The fatty acid profile

describes the specific nature of fatty acids

occurring in fats and oils. The chemical and

physical properties of fats and oils and the

esters derived from them vary with the fatty

acid profile. Transesterification is the

process where an alcohol and an ester react

to form a different alcohol and a different

ester. For biodiesel, an ethyl ester reacts

with methanol to form a methyl ester and

ethanol. These ethyl esters react with

methanol to form biodiesel and glycerol. As

mentioned above, the purpose of

transesterification is to reduce the viscosity

of the oil so that it has properties closer to

that of regular diesel used in CI engines.

Methanol is the preferred alcohol for

obtaining biodiesel because it has the lowest

cost and it is readily available. However, for

the reaction to occur in a reasonable time, a

catalyst must be added to the mixture of the

vegetable oil and methanol to accelerate the

speed of a reaction.

Feedstock

Feedstocks for production of biodiesels are

vegetable oils (soybean, canola, palm, and

rapeseed), animal fats (beef, tallow, lard,

poultry fat, fish oils) or recycled grease (mix

of the above two). All of the above

feedstocks contain triglycerides, free fatty

acids (FFAs) and other contaminants. The

proportions vary in level depending on the

feedstock and these variables affect the

chemical reactions needed to transform the

primary raw materials (feedstock and

alcohol) to create the biodiesels.

Commercially available vegetable oils are

made up of a small percentage of FFAs, but

crude vegetable oil may contain more FFAs

and phospholipids, which are removed in

two processes: refining and degumming,

respectively. The technology required