Page 1 of 11

Journal for Studies in Management and

Planning

Available at https://pen2print.org/index.php/jsmap/

ISSN: 2395-0463

Volume 04

Issue11

November 2018

Available online: https://pen2print.org/index.php/jsmap/ P a g e | 50

Characterization of Bauxite Residue in Bukit Goh,

Pahang, Malaysia

Edward Hingha Foday Junior*1

*

1Corresponding Author’s Email: hinghaja@gmail.com

Abstract

Red mud is described as a major industrial waste produced by the Bayer process for

the extraction of alumina from bauxite ores. The Red mud was collected from Bukit

Goh and it physical, chemical and mineralogical composition were investigated in

terms of it environmental effects. Because red mud has a lot of hazardous effect on

man and his environment, it intrinsic properties are characterised by high alkaline,

extremely saline, sodic and high heavy metals content. The pH, EC, Heavy Metals

and Mineral contents were analysed using pH meter, EC meter, ICPOES and XRD

respectively. The results show that, pH, EC and Heavy metals concentration of red

mud decreased with increasing storage time and Fe, Cd, As and Pb concentration

were determined. In general, the newly collected red mud retained more heavy

metals than the old red muds. The mineralogical composition of Calcite, Gibbsite,

Boehmite, Hematite, Siderite and Calcium aluminate decreased with increasing

storage time with large percentage of Calcite presence. Boehmite mineral

composition was completely removed from the 50days and 100days. It is fascinating

to know that Goethite, Magnetite, Sodium titanate and Sodalites increased with

increasing storage time.

Keywords: Red Mud, Bauxite, Electrical Conductivity, Heavy metals

1. Introduction

Bauxite residue is produced when the grinded ore is mixed with caustic soda

(NaOH), heated and put under pressure, and transformed into sodium aluminate and

insoluble solids (bauxite residue) . The entire process includes grinding, digestion,

liquor clarification, precipitation of alumina hydrate, and calcinations to alumina

(Jones et al 2011). Bauxite residue mud (BRM, also known as ‘red mud’) is an

alkaline, saline-sodic by-product of the Bayer process (Bayer, 1894) in which

alumina is extracted from its ore. Bauxite is crushed and heated in a 30% NaOH

solution in a two-step desilication-digestion process. According to Hind et al., 1998

Red mud (RM) is a waste by-product produced from its ore bauxite, in alumina

refinery industry by Bayer process. Bauxite ore is the only economic source of

alumina production worldwide today). Typical composition of industrially used

Page 2 of 11

Journal for Studies in Management and

Planning

Available at https://pen2print.org/index.php/jsmap/

ISSN: 2395-0463

Volume 04

Issue11

November 2018

Available online: https://pen2print.org/index.php/jsmap/ P a g e | 51

bauxite is: Al2O3 (40-60%), combined H2O (12-30%), Fe2O3 (7- 30%), SiO2 free and

combined (1-15%), TiO2 (3-4%), F, P2O5, V2O5 and others (0.05-0.2%)

(Josnamayee et al., 1998). Aluminate rich liquor, which is further processed to

produce alumina, is separated from bauxite residue waste after digestion. The solid

component of the residue slurry consists of undissolved bauxite impurities (iron and

Titanium oxides, and quartz), residual aluminium hydroxides (Gibbsite, Boehmite,

Diaspore) as well as insoluble precipitates (desilication product [DSP]): mostly

Sodalites Na8(AlSiO4)6Cl2(2)), tri-calcium aluminate hexahydrate (TCA:

3CaO.Al2O3.6H2O (s)): and Calcite (CaCO3) formed during the Bayer process (Grafe

et al., 2011). This waste slurry is then pumped to a fully contained deposition area

employing either wet stacking (also known as ‘Lagooning’: little

dewatering/thickening of slurry: deposit areas are usually in depressions in the

landscape and less than equal to 10m deep), or dry stacking (considerable dewatering

and thickening of slurry (usually to greater than equal to 45%w/w solids content)

deposit areas typically look like large hills and can be up to 50m high (Power et

al.,2011). Despite dewatering and rinsing of the slurry, Bauxite Residue is

approximately 50% w/w solids suspended in liquor which, without application of a

pre-deposition pH lowering treatment such as carbonation or seawater washing, has a

pH of 13 (cooling 2015). Bauxite Residue is brick red in colour and has slimy

appearance due to presence of high content of iron oxide and caustic soda. The

average particle size is about <10μm but few particles having size greater than 20

μm can also be found (Mohapatra et al., 2000). About 35% by weight of solids have

size less than 5 μm and 80% less than 8 μm. The sand, silt, clay of red mud is 3-5,

79- 80, 14-15% respectively. Bauxite possesses high surface area in the range of 13-

16 m2

/g with a true density of 3.30 g/cc (Paramguru et al., 2005). The free moisture

content of the Red Mud is highly variable (30-60%) depending upon the disposal

method. Red mud is mainly composed of iron oxides, quartz, sodium

aluminosilicates, calcium carbonate, aluminate, NaOH as Na2CO3, sodalite, ferrite

and titanium dioxide (generally present at trace levels) etc.

Bayer process is generally followed by two main steps for production of

aluminium throughout the world today, in the first step the crushed bauxite is

washed with concentrated caustic sodium hydroxide (NaOH) solution at elevated

temperatures up to 270°C (digestion). Under these conditions, the majority of the

aluminium containing molecules in the ore is dissolved into aluminium hydroxide

(Stubbs, 1997); the rest being an insoluble residue is called Red Mud which is

removed by settling: filtration processes (clarification). After solids separation (red

mud), aluminium trihydroxide (gibbsite; Al (OH)3) is precipitated by cooling the

solution and seeding with gibbsite, essentially reversing the initial dissolution

process (Grjotheim and Welch, 1998). In the second step, the gibbsite is removed

and washed prior to calcinations, where the gibbsite is converted to alumina (Al2O3)

Page 3 of 11

Journal for Studies in Management and

Planning

Available at https://pen2print.org/index.php/jsmap/

ISSN: 2395-0463

Volume 04

Issue11

November 2018

Available online: https://pen2print.org/index.php/jsmap/ P a g e | 52

to yield aluminium metal by Hall and Herroult method (Kirke, 1982). The use of

caustic soda (NaOH) at elevated temperature in the Bayer process results the bauxite

residue extremely saline, sodic and alkaline with a pH from 9 to 13 (Wong, 1990).

Although the introduction of Bayer’s process to the industries is an increasing

demand for manufacturing alumina, but accumulation of red mud at increasing rate

is a great problem throughout the world. It is in this regard, this research seeks to

characterize Red Mud from Bukit Goh, Pahang, Malaysia with particular reference

to Heavy metals, Mineral Composition, pH and Electrical Conductivity

2. Materials and methods

The Bauxite Red Mud sample used for this study was collected from Bukit Goh,

Pahang, Malaysia. The pH, EC, Mineral Composition and Heavy Metals

concentration were tested upon sample collection and was later kept in a plastic

container for subsequent experiment at a room temperature of 15-20oC. The sample

was tested for the following parameter (pH, EC, Mineral Composition and Heavy

Metals concentration) and was later stored for the period of 50 days and 100 days

respectively. The Bauxite Red Mud sample was air dried and crushed/ grinded with

hand to ensure homogeneity and sieved to pass through a 200-300 sieve holes before

storage. The Mineral analysis and Heavy Metals concentration of Bauxite Red Mud

was determined by X-Ray Diffraction and ICP OES respectively while pH and EC

were determined by pH meter (Orion 2 star pH benchtop) and EC meter (Orion 122

model) respectively.

In determining the pH and Electrical Conductivity (EC), Bauxite Red Mud was

diluted using deionized water with 5grams Bauxite Red Mud to 50mL deionized

water. The pH and EC of the various red mud ages (newly collected RM, 50days old

and 100days old) Bauxite Red Mud was determined by a calibrated pH meter and EC

meter respectively. Mineral Composition and Heavy metals concentration in the

Bauxite Red Mud were determined using X-Ray Diffraction (XRD) and ICPOES.

7.5mL of phosphoric acid (H3PO4) and 0.5mL nitric acid (HNO3) were used for the

preparation of samples and standard solution in determining the heavy metal

concentration. The Elemental composition of the Red Mud used for this study was

determined through total microwave digestion according to US EPA SW 846

Method 3051A (US EPA, 1998). The total concentration of heavy metals content in

the soil were determined by adding H3PO4 and HNO3 for the acid digestion method

under the temperature of 220OC. The digested solution was analysed for the heavy

metals content using Inductively Coupled Plasma Optical Emission

Spectrophotometer (ICPOES, Agilent 710 model). Historically, Bauxite Red Mud is

contaminated with heavy metals and Iron (Fe), Cadmium (Cd), Arsenic (As) and

Lead (Pb) concentration were determined. Microwave acid digestion was done in

order to enhance the operation of the ICPOES. The advantage of microwave-assisted