Page 1 of 4

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 05

May 2019

Available online:https://ejbss.org/ P a g e | 823

Influence Of Volume Of Paste On Freshand Hardened Properties Of Concrete

S.K. ARUNJITH KUDOS

DEPARTMENT OF CIVIL ENGINEERING

PRIST (Deemed to be University), THANJAVUR.

ABSTRACT

The term see refers to a new special type of concrete mixture characterized by high

resistance to segregation that can flow through intricate geometrical configuration in the

presence of reinforcement under its own mass without vibration and compaction. See

generally possesses a high powder content which keeps the concrete cohesive with high

flowability. A high substantial part of this powder could contain fillers like fly ash, crushed

rock fines, silica fumes etc. Volume of coarse aggregate, paste, powder, dosage of super

plastizet, mixing method plays an important role in the flowability and other requirements of

SCC. SCC has been made by many research workers and others with filler like fly ash.

INTRODUCTION

During the last few years due to

technological advances our conceptual

thinking about concrete has changed

considerably. It is now well understood

that one can influence the properties of

concrete greatly by even minor changes in

the composition. There has been increased

construction of large concrete structures

with increasingly complicated designed

shapes having congestedreinforcements.

This often leads to difficult casting

conditions and skilled labour shortage

hasbecome serious problem at construction

site. These events marked the appearance

of new typesof concrete which have been

developed in accordance with these needs.

Self compacting concrete (SCC) was first

developed in Japan based on

developmental work atthe University of

Tokyo, to offset a growing shortage of

skilled labour. The concept of see

wasproposed by Okamural in 1986. It is a

high fluid mix that has excellent

deformability and

resistance to segregation, that could

entirely fill and self compact under its own

weight in heavyreinforced form work.

SCC that is highly workable, easy to place

in the formwork and require novibration

has been more or less now globalised in

Page 2 of 4

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 05

May 2019

Available online:https://ejbss.org/ P a g e | 824

the last few years and is gaining

importancethroughout the world.

To achieve SCC, the concrete must be

highly fluid and stable I.e., the concrete

mix must remainhomogenous during the

entire process from plant to formwork

without separation of theaggregate, mortar

and water. SCC is a very promising

material since there is an implicit

assurance of uniform quality unaffected by

placement errors and poor compaction.

SCC generally requires a hyper-Plasticizer

to ensure fluidity and flow for a sufficient

length of time without experiencing a large

·slump loss·. Viscosity Modifying

Admixtures [resins, colloidalmatter] are

also sometimes added to ensure stable and

fully cohesive mixture even

whensubjected to vagaries at construction

sites such as varying moisture contents of

aggregates,accidental excess water,

ambient temperature and humidity

variations and others.

SCC mixes contains a large quantity of

powder materials as these are required to

maintain sufficient yield value of the fresh

mix, to reduce bleeding, segregation and

settlement. SCC has gained wide use in

many countries for different application

and high structural configurations.SCC

requires a high slump that easily be

achieved by incorporating the chemical

admixtures. SCC also plays a major role in

increasing the utilization of Industrial by- products like Slag, Crushed Rock Fines,

Fly Ash and Silica fume. It offers

possibilities for the utilization of fly ash,

which are currently the bi-products, with

minimal practical applications and which

are expensive to dispose of.

EXPERIMENTAL PROGRAMME

Mix design procedure to fabricate SCC

From the published literature so far it can

be said that the sec mixes can be

developed by takingthe V p (i.e., sum of

volume fractions of cement, filler and

water) with a mean value of 0.38 witha

variation of about ± 0.03 barring a few

mixes. Exceptions are seen, since,

flowability is alsoinfluenced by aggregate

shape, gradation of sand, type and amount

of superplasticizer used. In most of the

SCC mixes arrived in India it is observed

that the fine aggregate volume

ispredominantly more compared with the

coarse aggregate volume. The paste

volume used isgenerally higher due to

angular crushed aggregate which demand

more amount of water to coatthe surface of

aggregates.

Page 3 of 4

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 05

May 2019

Available online:https://ejbss.org/ P a g e | 825

It is possible to proportion SCC mixes for

a given strength and flowability by

keeping the pastecontent constant and by

increasing or decreasing the filler content

vis-avis the cement. Keepingall other

parameters constant and only by changing

the amount and filler quantities with in

aconstant paste volume, different grades of

concrete can be arrived at and a mix

design method inthe lines of the absolute

volume method can be evolved.

Mix design method adopted was by

starting with a fixed volume of paste (V p

= V cement + Vfiller + V water + V sp).

Further the water was fixed at 190 Itlm3

for all the trials and differentvolumes of

powder were considered (V pow = V

cement + V filler). For each paste content

thevolume of cement and flyash was

changed by keeping the water constant, to

get differentstrengths of concrete. The

cement content is taken in the range of 300

kg/m3 to 450 kg/m.

Correspondingly, the volume of flyash was

calculated based on the absolute volume of

the fixedpaste content and the chosen

cement content. Taking the total volume of

concrete as one unit, thefinal volume of

aggregates can be calculated by deducting

the volume of paste from the unitvolume.

Based on the literature survey and the

experience with the materials used in

thelaboratory, the ratios of CA and FA can

be fixed. The optimum dosage of super

plasticizer wasdecided by conducting the

'Marsh Cone Test" with the powder and

water.

RESULTS AND DISCUSSION

As discussed in Mix design procedure in

section 4.3.1, the Vp considered in this

study are 0.39,0.41 and 0.43. The total

powder content is in the range of 517

kg/m3 to 653 kg/m. WIP byvolume ranges

from 0.79 to 0.95 and by mass from 0.29

to 0.37. The quantities of cement

considered are 300 kg/m3

, 390 kg/m3

and

450 kg/m3

for each paste content, the

range specifiedby IS 456 from durability

considerations. For all the trials, water was

fixed at 190 lt/m: The w/cratio

corresponding to cement content 300

kg/m3

, 390 kg/m3

and 450 kg/m3

are 0.63,

0.49 and0.42. The ratio of fine and coarse

aggregates were taken based on the trial

mixes developedpreviously in the same

laboratory by the earlier researchers using

similar type of materials asused in this

study. The ratio is taken as 60:40 and the

optimum dosages of SP was fixed based

onthe Marsh cone test results.