Page 1 of 9

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online: https://ejbss.org/ P a g e | 1815

Processing and Mechanical & Thermal Properties of Mudar Fiber

Reinforced Epoxy Composite

C. Selva Rama Subramanian1 pg scholar PRIST University Thanjavur.

Dr.B. Selva Sundaram2

,M.E.,Ph.D.,Assistant professor Einstein College of Engineering Tirunelveli

Abstract- The present work deals with the processing and mechanical & Thermal properties of Mudar fiber

reinforced epoxy composite. The mudar fibers were aligned by randomly and were prepared in square plate shape.

The mechanical properties like tensile. Compression and flexural strength were tested by varying the wt% of fiber

like 15%.20%.30% and 40% both treated and untreated fiber

Key words; Mudar fiber, treated and untreated fiber, Noah, Mechanical properties tensile, compression & flexural

strength

I. INTRODUCTION

A composite is a structural material that is

widely used for light weight and high strength

applications. It is commonly used in aerospace,

automobile and defence vehicles. General fiber

reinforced composites are combined of fiber and

matrix. The important function of the fibers is take

the loads along their longitudinal directions.

Modern composite materials constitute a

significant proportion of the engineered materials

market ranging from everyday products to

sophisticated niche applications. While composites

have already proven their worth as weight-saving

materials, the current challenge is to make them cost

effective. The efforts to produce economically

attractive composite components have resulted in

several innovative manufacturing techniques

currently being used in the composites industry.

It is obvious, especially for composites, that

the improvement in manufacturing technology alone

is not enough to overcome the cost hurdle. It is

essential that there be an integrated effort in design,

material, process, tooling, quality assurance,

manufacturing, and even program management for

composites to become competitive with metals.

The composites industry has begun to

recognize that the commercial applications of

composites promise to offer much larger business

opportunities than the aerospace sector due to the

sheer size of transportation industry. Thus the shift of

composite applications from aircraft to other

commercial uses has become prominent in recent

years.

Increasingly enabled by the introduction of

newer polymer resin matrix materials and high

performance reinforcement fibers of glass, carbon

and aramid, the penetration of these advanced

materials has witnessed a steady expansion in uses

and volume.

Most commonly used matrix materials are

polymeric. In general the mechanical properties of

polymers are inadequate for many structural

purposes. In particular their strength and stiffness are

low compared to metals and ceramics. These

difficulties are overcome by reinforcing other

materials with polymers. Secondly the processing of

polymer matrix composites need not involve high

pressure and does not require high temperature. Also

equipments required for manufacturing polymer

matrix composites are simpler.

Composites are used because overall

properties of the composites are superior to those of

the individual components for example

polymer/ceramic. Composites have a greater

modulus than the polymer component but are not as

brittle as ceramics.

They included roof for housing application,

structural panels and unit beams were manufactured

out of soybean oil based resin and natural fibers

(flax, cellulose, pulp, recycled paper, chicken

Page 2 of 9

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online: https://ejbss.org/ P a g e | 1816

eathers) using vacuum assisted resin transfer molding

(VARTM) technology. Natural fiber reinforcement

of 20–55 wt % fiber increased the flexural modulus

to 2–6 GPa. The same resin reinforced with woven

E-glass gave a flexural modulus of 17 GPa. [1]

Scanning electron microscopy revealed some

interaction between the polymer and keratin feather

fiber. Physical property testing and microscopy show

some interaction between the fiber and polymer

without the need for coupling agents or chemical

treatment of the fibers. The density of the composite

upon introduction of keratin feather fiber is not

increased, but reduced by 2%. [2]

Glass fiber hybrid composites. Two types of

specimens are prepared, one by mixing the Palmyra

and glass fiber and the other by sandwiching Palmyra

fiber between the glass fiber mats. Composite plates

are prepared for different Palmyra/glass fiber weight

ratio. The tensile, bending, shear and impact

properties of roof light resin, Palmyra/glass fiber

hybrid composites are studied. The mechanical

properties increased due to hybridization.[3]

Composite Materials in pipes and pressure vessels.

Specimens cut from pipes made from composite

materials were tested under internal pressure loadings

have been tested by using a series of ASTM

Standards test methods for mechanical properties.

Good agreement was achieved between the

experimental results and analytical results.[4]

An alternative raw material for fiber- reinforced composite (FRC) . It is found that there

are statistically significant differences in the bark and

seed fiber dimensions. The bark fibers are long, with

a thin wall relative to their diameter, and are

therefore lightweight. The seed and bark fibers are

very similar to hard- and soft-woods, in terms of

chemical compositions and fiber dimensions,

respectively. Analyses conducted in this study

showed that there is a significant variation in the

holocellulose contents of the fractions of Mudar. The

higher content of holocellulose for bark fiber

provides a mechanical property of Mudar fibers are

in the range of non wood plant fibers.[5]

Reviewed the most suitable and commonly

used biodegradable polymer matrices and NF

reinforcements in eco-composites and nano

composites, with special focus on PLA Poly (lactic

acid) based materials. They concluded that, these can

represent an effective solution to the waste disposal

problem of polymer based materials.[6]

They said that before using the natural fiber,

the Fiber should be washed with 10% NaOH solution

and rinsed in hot water to remove the cellulose from

fiber surface for getting better binding with polymer

matrix. [7] The mean tensile strength, mean tensile

modulus and flexural modulus of vakka fiber

composite are much higher than those of sisal and

banana composites and comparable to that of

bamboo composite. The dielectric strength of vakka

fiber composites increases with increase in volume

fraction of fiber in the composite which is rare

phenomenon not observed in many of the natural

fiber composites. [8]

They Explained the resin, hardner standards

and density, Mould preparation, Casting of slabs,

Curing and sample preparation. They conclude that

the compressive strength has been found to increase

with increase in fly ash particles. In SEM analysis it

has been found that fly-ash particles have been

uniformly segregated.[9] Fibers treated with 5%,

10% and 15% NaOH and the effect of alkali

treatments on the fiber properties were explored. It is

concluded that 5% alkali treatment to the fibers

favored better mechanical properties to the Borassus

fruit fibers than the raw, 10% and 15% alkali treated

fibers. Hence the 5% NaOH treated Borassus fruit

fibers could be used as reinforcement in the

composites for structural applications.[10]

The results revealed that reinforcement of

epoxy with treated kenaf fibers increased the flexural

strength of the composite by about 36%, The

untreated fibers introduced 20% improvement. The

maximum strength of epoxy is about 225–250 MPa.

The treated kenaf fibers highly improved the flexural

strength of the epoxy composite which reached about

300–350 Mpa. [11] The simple hand lay-up

Page 3 of 9

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online: https://ejbss.org/ P a g e | 1817

technique to prepare the composite specimen of

Snake grass in to polyester with various fiber length

(10,30,60,90,120,150 mm) and volume fractions (Vf)

like 10%, 15%, 20%, 25% and 30% respectively. The

maximum tensile strength and modulus of the

chopped fiber isophthallic polyester composite is

achieved at 25% Vf for the 30 mm fiber length.[12]

The work includes the Analysis of Palmyra

Fiber Reinforced Epoxy Composites using FEA with

various fiber volume fractions and these results were

validated with the experimental result. The

experimental results were compared with the

analytical result and error percentage was

determined. The error % is higher in untreated fiber

than 5% NAOH treated fiber. [13]

II. EXPERIMENTAL PROCEDURE

2.1 Extraction of fibers

The mudar fibers were extracted from dried

barks of CG plant. The CG plant is a shrub growing

up to 4 m height. These plants mostly grow in dry

areas. The fiber can be obtained from both seed and

bark. The seed fiber can be extracted by drying the

seeds in sunlight for two days and the seeds are

opened out, the fiber will be with bunch of seeds, the

seeds have to be removed to obtained seed fiber. The

barks are pealed out from CG plant and dipped in

water for 2 weeks and skin was separated. The fiber

is extracted manually from bark and the extracted

fiber is allowed to dry in room temperature for 7

days. The length of extracted fiber varies from 50mm

to 80mm this is because of presents of notches. The

seed fibers are easier to extract and it is very soft in

nature. The bark fiber has better mechanical

properties than seed fiber. The fiber for this research

was collected from plants in southern part of India.

2.2 Fibers alkaline treatment

The extracted mudar fibers have

holocellulose content present on the surface of fiber.

The NaOH treatment removes little amount of

cellulose from surface of fiber and removes the firing

particles and dirt. Mudar fibers were treated with 5%

sodium hydroxide solution at 300C, by dipping in the

alkali solution for 1h. [10] The fibers were then

washed with tap water repeatedly, neutralized with

dilute acetic acid, again washed with distilled water,

and dried in sun light for a period of 24 h.

2.3 Mould Preparation

The mould was prepared for

the size of 280x280x3mm3

and

280x55x3 mm3

. Figure 2.1 shows the

mould for the size of 280x280x3 mm3

.

The mould is made with a base plate of

10mm thickness and 3mm stripes are

bolted all around with distance

of280mm.

Figure 2.1 Mould for the size of

280x280x3mm3

2.4 Specimen preparation

Area of epoxy = 28x5.5x0.3=46.2cm3

Wight of epoxy=46.2cm3 x

1.1 g/cm3 =50.82g

Ω 50g