Page 1 of 7

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online:https://ejbss.org/P a g e 1270

PERFORMANCE ANALYSIS OF C.I. ENGINE USING

VEGETABLE OIL

HERALD ARULKUMAR.N

PG Student,

PRIST Deemed to be University, Thanjavur

Abstract - The main aim of this work is to find out the various

combustion parameters, performance parameters and

emissions levels of any biodiesel with minimum inputs such as

density, calorific value, chemical formula, specific heat,

kinematic viscosity to the program. From the results, it is found

that the heat release and work done are reduced by about 4%

for Jatropha, 6% for Mahua and 8% for Neem oil esters when

compared to diesel. The peak pressure for vegetable oil esters

are reduced by about 3%, 4% and 5% respectively for

Jatropha, Mahua and Neem oil esters at an optimum engine

condition when compared to diesel.

Keywords- Jatropha, Mahua, Neem oils

I. Introduction

Diesel engines dominate the field of commercial

transportation and agricultural machinery on account of its

superior fuel efficiency. Cost and limited reserves of

conventional fossil fuels have intensified the search for

alternative fuels for use in internal combustion engines.

Vegetable oil is a possible alternative engine fuel because it

is clean burning, renewable, non- toxic, biodegradable and

environmental friendly transportation fuel. It can be used in

neat form without any modification of the engine. They can

be produced from the plants grown in rural areas. Vegetable

oils are produced from crops such as soybean, peanut,

sunflower, cotton, jatropha, mahua, neem, coconut, linseed,

mustard, karanja, rape and castor. The botanical name of the

jatropha shrub is jatropha curcas. Typically it is a drought

resistant shrub, growing up to 4-5 feet tall, yielding 4 tons

seed per acre under good irrigation. The madhuca indica oil

is obtained from well-dried kernels. The madhuca indica tree

is a drought resistant and deciduous. The results show that

the use of oil having long chain hydrocarbon structure have

better ignition characteristics.

However they causes, serious problems such as carbon

deposits buildup, poor durability, high density, high

viscosity, lower calorific value, more molecular weight and

poor combustion.

These problems can be rectified by transesterification

process. In this investigation, the engine performances of

a C.I engine using three vegetable oil esters like Jatropha,

Mahua, and Neem oils are obtained and compared with

diesel.

II. Theoretical Considerations

Diesel engines are exclusively significant with varied

operational systems of heterogeneous and transients

modes. An ideal engine shall have the ability to sustain

various temperatures, flow of gases and several

compositions of functional operations. From the

functioning study, it is generally observed that, a

comprehensive analytical solution to a problem cannot be

arrived at a diesel combustion process of complexities.

Nowaday’s computerized analysis are being carried out to

obtain accuracy. Yet, it is ever likely that an accurate

correlation between experimental results and

computerized module engines. However, the combustion

process can be altered or modified in tune with exhaust

emission. There have been increased attempts with two- zone model being replaced with four zone model of diesel

combustion processes. This is due to the fact that the two

zone model exerted an approximate the solution with

regard to temperature and strength of the gradients inside

the diesel combustion chamber. Normally, a two zone

model comprises a burning zone and a non-burning zone.

In the burning zone, a conical shape with a specific cone

angle containing air resulting with a fuel spray and

combustion products are found. The space lying vacant in

the cylinder is assumed to be non burning zone. Fig.1

represents the proposed four zone model which is

supposed to yield a grater extent of accuracy.

Page 2 of 7

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online:https://ejbss.org/P a g e 1271

Fig.1. Schematic layout of multi zone combustion model

Nevertheless, there is no great level of deviation from

the conventional or basic concepts. Factors like jet

penetration, preparation rate, fuels spray, impingement rate,

and reaction rate of heat are all retained.

III.Biodiesel Preparation

To standardize the process conditions, initial trials were

conducted with mahua oil (100 grams) by varying amount of

alcohol, reaction temperature and reaction time. The mixture

of mahua oil (2000g) and methanol /ethanol (150% excess

on mole basis) (6% in vol. basis) were boiled in a reaction

chamber fitted with condenser at a temperature of 65-75 ̊C

for 5 hours.

Then the top layer was separated and vacuum was

distilled to recover methanol /ethanol. Later, the ester was

washed with alkali solution (calcium carbonate) to reduce the

pH to neutral and washed with salt water (5%). The product

was then dried in an oven for an hour to remove the traces of

water. The physical and chemical properties of vegetable oil

esters were measured before and after transesterification of

vegetable oil.

III. The Engine And Dynamometer

The performance test was carried out on a single cylinder,

four stroke naturally aspirated, and water-cooled, single

cylinder Kirloskar computerized diesel engine test rig.

Diesel engine was

directly coupled to an eddy current

dynamometer. It is shown in Fig.2.

Fig. 2. Experimental setup

The engine and dynamometer are interfaced to a control

panel, which was connected to a computer.

This computerized test rig was used for recording the test

parameters such as fuel flow rate, air flow rate,

temperature and load for calculating the engine

performance, namely cylinder pressure, brake power,

brake specific fuel consumption, brake thermal efficiency,

and emission like HC, CO, NOx and smoke. A whole set

of experiments were conducted at the engine speed of

1500 rpm and compression ratio of 17.5:1.

IV. Experimental Setup

The experiments were conducted at the injection timing of

14°bTDC and 200-bar injector opening pressure for low

load, part load and full load with diesel fuel.

Page 3 of 7

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online:https://ejbss.org/P a g e 1272

After setting the engine speed and load to the required

values, the following observations and subsequent

calculations were made,

1) Time for 60cc of fuel consumption (sec)

2) Exhaust gas temperature

3) Water inlet and outlet temperature.

4) Air flow rate.

5) Pressure, harmful pollutants like HC, CO, NOx and

smoke are recorded for various Loads condition.

6) Brake Power, Thermal efficiency, and Specific fuel

consumption were calculated.

The experimental work was carried out on a single

cylinder water cooled engine. The engine is coupled to a

Saj Test Plant Pvt. Ltd. to make eddy current

dynamometer. In cylinder, gas pressure histories were

measured using a kistler pressure transducer flush mounted

inside the cylinder head. The electric charge from the

transducer was converted into voltage by a charge

amplifier. The engine was also mounted with a shaft

encoder, which provided pulses at one degree of crank

angle resolution. This encoder provided clock and trigger

signals for the high speed measurements. Collection of the

above data was carried out using windows based data

acquisition system. This data acquisition system is able to

collect and average up to 1,000 cycles of data.

The exhaust gas was made to pass through the probe of

crypton computerized exhaust gas analyzer for the

measurement of HC, CO, NOx and later passed through

the probe of smoke meter of Bosch type for the

measurement of smoke opacity. A thermocouple was fixed

at the exhaust manifold to measure the exhaust gas

temperature.

V. Observations Made

1. The engine was tested under different load conditions

for speed 1500 rpm.

2. The time of 60 CC of fuel consumption was noted

down for each load condition.

3. The mass flow rate of air was estimated by using a

water

manometer, air drum and an orifice plate arrangement.

4. The cylinder pressure was measured by using the piezo

electric pressure transducer, charge amplifier and

storage

oscilloscope.

5. The pollutants CO, HC, NOx were measured by

Crypton

computerized emission Analyzer.

6. The smoke was measured by a Bosch type smoke

meter.

V. Results And Discussion

Comparison of predicted combustion characteristics of

vegetable oil esters with diesel

Esterified vegetable oil contains good physical and chemical

properties such as high cetane number, high Calorific value,

low density, better atomization and vaporization, better

spray characteristics in the combustion chamber, and high

burning rate. These properties lead to effective utilization of

air which results in complete combustion. Fig.3 shows the

variation of theoretical pressure with respect to crank angle

for different vegetable oil esters along with diesel. The

optimum cylinder pressure is predicted for 75% of load,

injection timing of 14o bTDC and spray cone angle of 18°.

The peak pressure obtained for diesel, jatropha, mahua and

neem esters are 79 bar, 77 bar, 76 bar and 74 bar

respectively as seen in the Fig.3. It is inferred from the Fig.3

that cylinder pressure variation between biodiesel and diesel

is nominal that is about 3 % to 5 % only. After esterification,

vegetable oil properties such as density, calorific value and

cetane number are improved. These parameters are

responsible for bringing the cylinder pressure of vegetable

oil esters at par with that of diesel fuel.

Fig.4 shows the variation of theoretical rate of pressure rise

with respect to crank angle for vegetable oil esters along

with diesel. Rate of pressure raise increases with increase of

load for all fuels. The optimum cylinder pressure is

predicted for 75% of load, injection timing of 14o bTDC and

spray cone angle of 18°. It is seen from Fig.4 that the rate of

pressure raise of 5 bars, 4.8 bars, 4.7 bars, and 4.6 bars are

seen for the fuels such as diesel, jatropha, mahua, and neem

oil ‘esters’ respectively. From the Fig.4, it is inferred that

the rate of pressure raise variation between biodiesel and

diesel is nominal, i.e. about 3 % to 6 % only. After

esterification, vegetable oil properties such as density,