Page 1 of 20

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online:https://ejbss.org/ P a g e | 1232

Implementation Of Nanofluid As Coolant In An Automobile

Applications

Aruvi.S

ABSTRACT

Development of high-performance automobile engines has led the designers to

look for radiators with high heat transfer rates. One of the ways to upgrade the heat

transfer rate is by selecting a coolant with high thermal conductivity. The

primeobjective of the present work is to study the performance characteristics of Al2 O3

-water nanofluid in the radiator of a 4-Cylinder, 4-stroke, vertical, stationary petrol

engine.

In thisworknanofluids are prepared in different volume fractions by dispersing

proper proportions of Al2O3nanoparticles in de-ionized water. Nanofluids are prepared in

different volume fractions with optimum processparameters.

The prepared nanofluids in different volume fractions are tested as coolants in

theradiator of a multi cylinder petrol engine test rig and heat transfer rates are

evaluated. These experiments are conducted at different engine speeds, loading of the

engine and air flow rates. Performance evaluation is done at different volume fractions

and flow rates of fluids.Reynolds number is decreasing with increase in volume fraction

at specified engine speeds whereas heat transfer coefficient increases as the volume

fraction increases under similar operating conditions.

1. INTRODUCTION

Continuous technological developments inautomobile industry focused

on improving the fuel efficiency of internal combustion engines. Fuel

efficiency is enhanced by maintaining the engine temperature at an optimum

Page 2 of 20

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online:https://ejbss.org/ P a g e | 1233

value which requires the engine heat to be extracted by circulating fluids like

water, ethylene glycol etc., around the engine. However, the application of

conventional fluids as coolants is limited bytheir low thermal conductivity

which has to be improved.

Thermal conductivity of these fluids can be improved by the addition of

solid particles as these particles possess higher thermal conductivity than those

of conventional liquids. The feasibility of usage of such suspensions with sizes

in the order of millimeters (or) micrometers was investigated earlier and

significant drawbacks were observed.

These drawbacks include sedimentation of particles, clogging erosion of

channel wells and increasing pressure drop which prevent their usage in

practical application. These drawbacks can be overcome by reducing the

particle size to nanoscale.

The particle sedimentation speed (Stokes law) is expressed by equation

(1), which indicates that the particle sedimentation speed depends on particle

size, base fluid viscosity and density difference between particle and base fluid.

The easiest way to be free from sedimentation is to minimize particle size as the

sedimentation speed goes to zero with nanometer-sizeparticle.

Nanofluids are not simply liquid-solid mixtures but are produced by

dispersing nanometer-scale solid particles into base liquids such as water, ethylene

glycol (EG), oils, etc without agglomeration. The two methods used for the

preparation of nanofluids are (i) one-step and (ii) two-step methods.

One-step method combines the production and dispersion of nanoparticles

Page 3 of 20

European Journal of Business &

Social Sciences

Available at https://ejbss.org/

ISSN: 2235-767X

Volume 07 Issue 04

April 2019

Available online:https://ejbss.org/ P a g e | 1234

in the base fluid in a single step as shown in fig.1. The limitations of this method

are the low production capacities and residual reactants leftin the nanofluid due to

incomplete chemical reaction.

Fig.1. One step nanofluid preparation technique

In two step method, nanoparticles are synthesized and then dispersed in

the base fluids.Two-step method is advantageous when massproduction of

nanofluids is considered. The disadvantage of the two-step technique is that the

nanoparticles form clusters without proper dispersion during the preparation of

the nanofluid.

Generally, ultrasonic equipment is used to intensively disperse the

particles and reduce clustering. Besides the application of ultrasonic waves,

other techniques such as control of pH of base fluid or addition of surface

active agents (surfactants) are used.

PARTICLE MATERIAL AND BASEFLUID

Particle materials in general used are metals, metal- oxides, carbides and nitrides.

Metal nanoparticles oxidize during preparation and their higher density leads to